manualshive.com logo in svg

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 189 / 314

Поделиться
Скачать
PIAGGIO 633929(IT) Скачать руководство пользователя страница 189

CIDENTALLY SWALLOWED, DRINK LARGE
QUANTITIES OF MILK OR WATER AND SEEK
MEDICAL ADVICE IMMEDIATELY. BRAKE
FLUID DESTROYS SKIN AND OCULAR TIS-
SUE. IF YOU ACCIDENTALLY SPILL BRAKE
FLUID ON YOURSELF, TAKE OFF YOUR
CLOTHES, WASH WITH HOT WATER AND
SOAP AND SEEK MEDICAL ADVICE IMMEDI-
ATELY. IF BRAKE LIQUID GETS ACCIDEN-
TALLY IN CONTACT WITH YOUR EYES, RINSE
WITH ABUNDANT FRESH WATER AND SEEK
MEDICAL ADVICE IMMEDIATELY. KEEP
BRAKE FLUID OUT OF THE REACH OF CHIL-
DREN.

Remove the 3 fixing screws indicated and remove

the whole geared motor.

Use a screwdriver to remove the plastic access

cover to the pump joint/geared motor

Unscrew the pump joint screw.

Unscrew the two geared motor pump locking

screws.

MP3 125

Suspensions

SUSP - 17

Содержание 633929(IT)



























































































































































































































































































































Отзывы:

Нет отзывов