PIAGGIO 633929(IT) Скачать руководство пользователя страница 140

Страница: 140 / 314

Assemble the limiting bell using the counterweight

fixing screw as a reference.

- Tighten the clamping screw to the prescribed tor-

que.

Locking torques (N*m)

Limiting bell screw

11 ÷ 15 Nm

Set the tensioner cursor to the rest position.

- Fit the chain tensioner on the cylinder, using a

new gasket, and tight the two screws to the pre-

scribed torque.

Insert the chain tensioning screw, together with the

spring and washer, tightening it to the prescribed

torque.

Locking torques (N*m)

Tensioner screws

11 ÷ 13

Tensioner cover

5 ÷

6 Nm

Adjust valve clearance

- Fit the spark plug.

Electrode distance 0.8 mm

Locking torques (N*m)

Spark plug

12 ÷ 14

Refit the cylinder head cover, tightening the 5 screws to the prescribed torque. Make sure the gasket

is positioned properly.

Remove the flywheel cover completely as already described in the flywheel chapter.

- Reassemble the oil pump control, the chain compartment cover, the by-pass and the oil sump as

described in the lubrication chapter.

- Reassemble the driving pulley, the belt and the transmission cover as described in the transmission

chapter.

Locking torques (N*m)

Tappet cover screws

6 - 7 Nm

TIMING SYSTEM COMPONENTS ASSEMBLY

Name

Torque in Nm

Tappet cover screws

6 - 7 Nm

Spark plug

12 ÷ 14

Tensioner cover

5 ÷ 6 Nm

Tensioner screws

11 ÷ 13

Limiting bell screw

11 ÷ 15 Nm

Engine

MP3 125

ENG - 46

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 140 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: