manualshive.com logo in svg

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 11 / 314

Поделиться
Скачать
PIAGGIO 633929(IT) Скачать руководство пользователя страница 11

Specification

Desc./Quantity

Battery

12V-12Ah

Generator

Three-phase alternating current

Frame and suspensions

FRAME AND SUSPENSIONS

Specification

Desc./Quantity

Chassis

Tubular and sheet steel.

Rear suspension

Single arm with two double-acting hydraulic shock

absorbers and preloading adjustable to 4 posi-

tions.

Front suspension

The tilt mechanism is composed of an articulated

parallelogram suspension with die-cast aluminium

control arms and two side headstocks plus shock

absorbers with hydraulic locking system.

Brakes

B

RAKES

Specification

Desc./Quantity

Front brake

Ø 240 mm double disk with hydraulic control acti-

vated by the handlebar right-hand lever.

Rear brake

Ø 240 mm disc brake with hydraulic control acti-

vated by the handlebar left-side lever.

Wheels and tyres

WHEELS AND TYRES

Specification

Desc./Quantity

Front wheel

Alloy rims: 12" x 3.00"

Rear wheel

Alloy rim: 12"x 3.50"

Front tyre

120/70-12", without inner tube

Rear tyre

Without inner tube: 130/70-12" 62P

TYRE PRESSURE

Specification

Desc./Quantity

Front tyre pressure (rider)

Front tyre pressure (rider): 1.6 bar

Front tyre pressure (rider and passenger)

Front tyre pressure (rider and passenger): 1.8 bar

Rear tyre pressure (rider)

Rear tyre pressure (rider): 2 bar

Rear wheel pressure (rider and passenger):

Rear tyre pressure (rider and passenger): 2.4 bar

N.B.

CHECK AND ADJUST TYRE PRESSURE WITH TYRES AT AMBIENT TEMPERATURE. REGU-
LATE PRESSURE ACCORDING TO THE WEIGHT OF THE RIDER AND ACCESSORIES

MP3 125

Characteristics

CHAR - 5

Содержание 633929(IT)



























































































































































































































































































































Отзывы:

Нет отзывов