PIAGGIO 633929(IT) Скачать руководство пользователя страница 194

Страница: 194 / 314

Refit the spring/toothed sector unit, hold the crank-

case in a perfectly horizontal and stable position,

place the spring/toothed sector unit keeping it per-

fectly perpendicular to the bearing already fitted on

the crankcase; if necessary, slightly hit the unit

shaft end with a mallet and protect the thread by

screwing in a nut.

Fit the pinion and align the reference on the pinion

teeth with the reference indicated on the second

slot of the toothed sector.

Grease the pinion and the toothed sector with spe-

cific grease.

Refit the toothed sector spacer.

Recommended products

MONTBLANC MOLYBDENUM GREASE

MON-

TBLANC MOLYBDENUM GREASE

Molybdenum disulphide grease

Lubricate the interference areas, match the crank-

case halves with slight hits of a mallet to get them

into contact.

Place the flexible transmission supporting bracket,

refit the four screws, screw them to the prescribed

torque.

Locking torques (N*m)

Geared motor crankcase halves coupling
screws

11 ÷ 13

Suspensions

MP3 125

SUSP - 22

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 194 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: