PIAGGIO 633929(IT) Скачать руководство пользователя страница 177

Страница: 177 / 314

Hydraulic system layout

When tilting is locked, the geared motor activates

the hydraulic pump indicated in the photograph

and pressurises the circuit.

The pressurised oil reaches the distribution frame

"T"

and the pressure sensor

"A".

Then, the pipes

branch out to reach the upper joints on the side

steering tubes.

Through the rigid-flexible pipes inside the side

steering tubes, the oil reaches the stem sliding

locking device placed parallel to the shock absorb-

er.

Steering tubes

Remove the brake calliper pipe retainers and the

hydraulic pipe fitting from the brake calliper making

sure there is a container to collect the brake fluid.

MP3 125

Suspensions

SUSP - 5

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 177 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: