PIAGGIO 633929(IT) Скачать руководство пользователя страница 154

Страница: 154 / 314

Refitting

- Fit the internal bulkhead by locking the two

screws to the prescribed torque.

- Fit the oil filter fitting and tighten it to the specified

torque.

- Place a new gasket on one of the crankcase

halves, preferably on the transmission side, to-

gether with the locating dowels.

- Lubricate the main bushings and insert the crank-

shaft in the transmission side crankcase half.

- Reassemble the two crankcase halves.

For the 200 models reposition the shim washers

as in the original fitting.

- Fit the 11 screws and tighten them to the pre-

scribed torque.

- Lubricate the flywheel oil seal.

- Using the appropriate tool, assemble the oil seal.

- Fit a new O-ring on the pre-filter and lubricate it.

- Insert the filter on the engine with the relative cap.

Tighten to the specified torque.

N.B.

FAILURE TO USE THE SPECIFIC TOOL CAN
RESULT IN AN INCORRECT DEPTH POSITION
AND AS A CONSEQUENCE IN INADEQUATE
OIL SEALING.

Specific tooling

020425Y

Punch for flywheel-side oil seal

Locking torques (N*m)

Internal engine crankcase bulkhead (transmis-
sion-side half shaft) screws

4 ÷ 6

Oil filter on

crankcase fitting

27 ÷ 33

Engine-crankcase

coupling screws

11 ÷ 13

Engine oil drainage

plug/mesh filter

24 ÷ 30

Engine

MP3 125

ENG - 60

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 154 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: