PIAGGIO 633929(IT) Скачать руководство пользователя страница 44

Страница: 44 / 314

UPON REPLACING HUB OIL, AVOID THE OIL
COMING INTO CONTACT WITH THE REAR
BRAKE DISC.

Recommended products

AGIP ROTRA 80W-90

Rear hub oil

SAE 80W/90 Oil that exceeds the requirements of

API GL3 specifications

Check

- Rest the vehicle on its centre stand on an even surface. - Unscrew the oil dipstick, dry it with a clean

cloth and reinsert it, screwing it in thoroughly.- Take out the dipstick and check that the oil level reaches

the 2nd notch from the bottom.- Screw the dipstick back into place completely.

Recommended products

AGIP ROTRA 80W-90

Rear hub oil

SAE 80W/90 Oil that exceeds the requirements of API GL3 specifications

Locking torques (N*m)

Hub oil drainage plug

15 ÷ 17

Replacement

-Remove the oil cap «

».

- Unscrew the oil drainage cap "

" and drain out

all the oil.

- Screw on the drainage plug and fill up the hub

with oil (about 150 cc)

Air filter

Remove the air cleaner cap after undoing the re-

tainer screws, then extract the filter.

- Wash with water and neutral soap.

-Dry with a clean cloth and short blasts of com-

pressed air.

- Soak with a mixture of 50% petrol and 50%

SE-

LENIA AIR FILTER OIL

Maintenance

MP3 125

MAIN - 10

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 44 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: