manualshive.com logo in svg

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 257 / 314

Поделиться
Скачать
PIAGGIO 633929(IT) Скачать руководство пользователя страница 257

•

Lower ring nut for central steering tube

•

Upper ring nut for central steering tubes

•

Constant-velocity universal joints

Electrical system

• Battery

• Main switch

• Lights: high beams, low beams, side/taillights (front and rear) and relevant warning lights

- Regulating the headlights according to the regulations currently in force

• Front and rear stop light buttons and bulb

• Turn indicators and their warning lights

• Instrument lighting

• instruments: fuel and temperature indicator

•Instrument panel lights

• Horn

• electric start up

• Engine stopping with emergency stop switch

• Electric opening of saddle with remote control

• Tilting system locking - unlocking button

CAUTION

TO ENSURE MAXIMUM PERFORMANCE, THE BATTERY MUST BE CHARGED BEFORE USE.
INADEQUATE CHARGING OF THE BATTERY WITH A LOW LEVEL OF ELECTROLYTE BEFORE
IT IS FIRST USED SHORTENS THE LIFE OF THE BATTERY.

CAUTION

WHEN INSTALLING THE BATTERY, ATTACH THE POSITIVE LEAD FIRST AND THEN THE NEG-
ATIVE LEAD.

WARNING

BATTERY ELECTROLYTE IS TOXIC AND IT MAY CAUSE SERIOUS BURNS. IT CONTAINS SUL-
PHURIC ACID. AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
IN CASE OF CONTACT WITH EYES OR SKIN, RINSE WITH ABUNDANT WATER FOR ABOUT 15
MINUTES AND SEEK MEDICAL ATTENTION AT ONCE.
IF IT IS SWALLOWED, IMMEDIATELY DRINK LARGE QUANTITIES OF WATER OR VEGETABLE
OIL. SEEK IMMEDIATE MEDICAL ATTENTION.
THE BATTERIES PRODUCE EXPLOSIVE GAS; KEEP THEM AWAY FROM NAKED FLAMES,
SPARKS AND CIGARETTES. IF THE BATTERY IS CHARGED IN A CLOSED PLACE, TAKE CARE
TO ENSURE ADEQUATE VENTILATION. ALWAYS PROTECT YOUR EYES WHEN WORKING
CLOSE TO BATTERIES.
KEEP OUT OF THE REACH OF CHILDREN

CAUTION

NEVER USE FUSES WITH A CAPACITY HIGHER THAN THE RECOMMENDED CAPACITY. USING
A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE
A FIRE.

Levels check

Level check:

MP3 125

Pre-delivery

PRE DE - 3

Содержание 633929(IT)



























































































































































































































































































































Отзывы:

Нет отзывов