PIAGGIO 633929(IT) Скачать руководство пользователя страница 207

Страница: 207 / 314

With interface wiring connected to the control unit,

secure the vehicle on its centre stand and switch

to "ON". Select the reading scale on 20 V. Insert

the multimeter probes on pins 17 (black) and 25

(red). Check that the voltage in the activated lock-

ing condition is 4V and 1V in the locking rest

condition.

With the interface wiring disconnected from the

control unit, check the continuity between pin 17

and the yellow cable of the potentiometer connec-

tor, between pin 25 and the green-blue cable,

between pin 11 and the orange-blue cable. Also

check that these lines are insulated from each oth-

er and earth.

TILT LOCKING-UNLOCKING SWITCH

MP3 125

Suspensions

SUSP - 35

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 207 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: