PIAGGIO 633929(IT) Скачать руководство пользователя страница 86

Страница: 86 / 314

12-WAY INSTRUMENT CONNECTOR

Specification

Desc./Quantity

Lighting

Battery positive

Earth

Live positive lead

Remote seat opening

Zeroing

- Remove the left side fairing to access the saddle

opening receiver control unit indicated in the pho-

tograph

- Remove the metal terminal and connect it to a

good earth point, or to terminal 7 (black), for at

least 10 seconds.

- In this operation all the remote controls stored in

the control unit will be deleted.

WARNING

THE CONTROL UNIT CAN PROGRAMME UP
TO 8 REMOTE CONTROLS.

Programming

Follow these steps to program the remote controls:

. Insert the remote control key to be programmed in the steering lock key block.

Electrical system

MP3 125

ELE SYS - 26

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 86 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: