PIAGGIO 633929(IT) Скачать руководство пользователя страница 233

Страница: 233 / 314

Unscrew the braking splitter screw.

Disconnect the brake pipes removing the two met-

allic straps indicated in the figure.

Remove the brake oil tube fitting from the rigid pipe

inside the front suspension arm and loosen the

hydraulic joint fixing nut of the suspension locking

to release the brake pipes.

Front brake pipes removal

Remove front Shield.

Remove front wheel and mudguard.

Disconnect the brake pipes from the calliper and

drain the brake fluid.

Then, remove the plastic and metallic straps.

Unscrew the brake pump pipes as indicated in the

figure.

MP3 125

Braking system

BRAK SYS - 5

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 233 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: