PIAGGIO 633929(IT) Скачать руководство пользователя страница 155

Страница: 155 / 314

Oil pump

- Check there are no signs of wear on the oil pump

shaft or body.

- Check there are no signs of scoring or wear on

the oil pump cover.

- If you detect non-conforming measurements or

scoring, replace the faulty parts or the unit.

- Fit the pump cover in the position that permits the

crankcase fixing screws to be aligned.

- Make sure the gasket is positioned properly and

refit the pump on the engine crankcase. The pump

can only be fitted in one position. - Tighten the

screws to the prescribed torque.

- Fit the sprocket wheel with a new O-ring.

- Fit the chain.

- Fit the central screw and the belleville washer.

Tighten to the prescribed torque.

- Fit the oil pump cover by tightening the two

screws to the prescribed torque.

N.B.

FIT THE BELLEVILLE WASHER SO THAT ITS
OUTER RIM TOUCHES THE PULLEY. MAKE
SURE THAT THE PUMP TURNS FREELY.

Locking torques (N*m)

Screws fixing oil pump to the crankcase

5 - 6

Oil pump control crown screw

10 ÷ 14

Oil pump

cover screws

0.7 ÷ 0.9

Removing the oil sump

- Remove the oil filler plug, the transmission cover,

the complete driving pulley assembly with belt and

the sprocket wheel, as described in the "Trans-

mission" chapter.

- Drain the oil as described previously.

- Remove the seven screws, shown in the dia-

gram, and the two rear brake fluid pipe fixing

brackets.

MP3 125

Engine

ENG - 61

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 155 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: