PIAGGIO 633929(IT) Скачать руководство пользователя страница 93

Страница: 93 / 314

- Disconnect the connectors from the flywheel wir-

ing as shown in the photo.

- Remove the cable from the retaining clip on the

flywheel cover.

Remove the lower screw of the left-hand shock

absorber.

- Use a jack to support the vehicle properly. Re-

move the engine-swinging arm fixing pin by undo-

ing the nut and the head of the pin as shown in the

photograph.

- The engine is now free.

When refitting the engine onto the scooter, carry out the removal operations but in reverse order and

respect the tightening torques shown in the Specifications Chapter.

-Check the engine oil level and if necessary top it up with the recommended type.

- Fill and bleed the cooling circuit.

- Check the functioning of the accelerator and the electrical devices.

CAUTION

MP3 125

Engine from vehicle

ENG VE - 5

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 93 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: