PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 95

Страница: 95 / 218

ASSAYS

PerkinElmer Life and Analytical Sciences

Background Subtract

Mark this box to subtract background CPM from all samples. The background

value is established in one of three ways and is selected from the following:

Vial

The instrument counts the first vial in the cassette for either ten minutes or the

defined protocol count time (whichever is greater) and establishes a CPM value

for each region; these are the background values subtracted from each sample

within each region of the assay.

IPA

The instrument subtracts the background values established during the calibration

and Instrument Performance Assessment (IPA) procedures from the entire

spectrum of the samples. The background spectra are stored during these

procedures and are available for any counting region.

Manual

Enter the CPM values you would like the instrument to subtract from the entire

spectrum of the samples.

Note: In Quench Standards assays, the 1

Vial background

subtraction option is not available. Background subtraction is only

applied to the reported data for quench standards and has no

impact on the spectrum for each standard. Any background

subtraction that occurs in DPM assays will apply to the quench

standards used for the purpose of recalculating the quench curve

in the DPM assay.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды