PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 40

Страница: 40 / 218

CHAPTER 2

PerkinElmer Life and Analytical Sciences

Note:Use the View menu and select Refresh to verify that you have

the latest view of the Replay files.

Figure 2-20 Replay Conditions Window.

5. In the Replay Conditions tab, define the parameters, as needed for reanalysis

of sample data.

6. In the Report Definition tab, define any printed or electronic reports you would

like to generate for the reanalysis of sample data.

7. Click the Replay button. Any reports that you defined are generated after the

reanalysis of data occurs.

Note: Data processed with Replay does not change the original

data. All Replay changes are temporary.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды