PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 164

Страница: 164 / 218

CHAPTER 8

154

PerkinElmer Life and Analytical Sciences

Background Subtraction

Mark this box if you would like to activate the Background Subtraction feature.

When this feature is activated, the instrument subtracts background values from

sample data prior to reanalysis in Replay. Choose a background source from the

drop down list.

Manual -

You can manually define background values for each of the three

regions, A, B, and C.

Vial - The instrument counts the first vial in the cassette for either ten

minutes or the defined protocol count time (whichever is greater) and

establishes a CPM value for each region; these are the background values

subtracted from each sample within each region of the assay.

Apply Half-life Correction

Mark this box if you would like to activate the Half-life Correction feature. When

this feature is activated, the instrument corrects the sample data for half-life

decay of the nuclide(s) being reanalyzed in Replay. The Reference Date and Time

are used to make the decay calculation. The default settings for the Reference

Date and Time correspond to the start of an assay

Replay

Click on Replay. The following Replay output windows are displayed in the main

window immediately after the data is reanalyzed.

If Quench Curves - Block Data is selected during Replay processing, only the

curve will be initially displayed. Double-click on this curve to view the Expanded

Quench Curve with the standard points and efficiency displayed.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды