PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 185

Страница: 185 / 218

MAINTENANCE

AND

TROUBLESHOOTING

PerkinElmer Life and Analytical Sciences

175

IPA error C-14 LCR.

The Carbon-14 source does not contain enough activity.

Check that the correct source is being used. Use a new source, if necessary.

IPA error-H-3 chi-square

The Chi-square test failed while counting the Tritium source.

Rerun the Chi-Square test. If the test fails, call PerkinElmer Technical Service.

IPA error-H-3 LCR.

Tritium source does not contain enough activity.

Check that the correct source is being used. Use a new source, if necessary.

LOST PIN POS.

A Sample changer error has occurred.

No action is required unless a message is printed. If this message appears on a

printout, call PerkinElmer Technical Service.

Missing Vial

This message indicates that a vial is missing from the cassette.

No Quench sets specified.

No quench set has been selected for the assay.

Select the appropriate quench set from the Quench Standards Library. If an

appropriate standard set does not exist, you must perform an appropriate Quench

Standards assay.

No quench standard is defined for this assay.

A standard that is being used by a sample nuclide in an assay has been

deselected.

Re-select the standard for the assay.

Normalization error-both tubes LCR.

The count rate in both photomultiplier tubes is too low.

Check that the unquenched Carbon-14 source is in sample position 1 in the

cassette. Call PerkinElmer Technical Service.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды