PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 18

Страница: 18 / 218

CHAPTER 2

PerkinElmer Life and Analytical Sciences

How to Perform the SNC (Self-Normalization and Calibration)

SNC for an Instrument without Super Low Level Counting Ability

1. Define the IPA parameters in the IPA Definition window.

Figure 2-1 IPA Definition Window.

2. Reset the SNC protocol flag to the reset position (the flag is all the way to the

left when the plug is on the left end of the cassette).

3. Load the purged, unquenched Carbon-14 standard into the first position of the

cassette (this is at the same end as the protocol plug).

Caution: Do not use the unpurged, Low Level standards to

calibrate the instrument, even if the instrument is to be used in

Low Level, High Sensitivity or Super Low Level count mode.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды