PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 12

Страница: 12 / 218

CHAPTER 1

PerkinElmer Life and Analytical Sciences

Efficiency

For Tritium in the range 0-18.6 keV, the minimum acceptable efficiency is 60%

(58% for 3170TR/SL). For Carbon-14 in the range 0-156keV, the minimum

acceptable efficiency is 95% (94% for 3170TR/SL). These values were generated

by PerkinElmer Life and Analytical Sciences at our Downers Grove, Illinois facility.

The exact values obtained at other instrument locations may vary. Counting

Efficiency is a parameter measured as part of Instrument Performance

Assessment (IPA). IPA is an option on the TriCarb

2800TR and 2900TR.

Chi-Square

Chi-Square acceptable range: 7.63 to 36.19, performed as 20, 0.5 minute repeat

counts and tested at the 99% confidence limits. Chi-Square is a parameter

measured as part of Instrument Performance Assessment (IPA). IPA is an option

on the Tri-Carb 2900TR

Physical Dimensions

The following table displays the physical dimensions of all TriCarb models:

Figure 1-2 Physical Dimensions

Detectors

Two diametrically opposed high performance photomultiplier tubes (PMTs) are

coupled to a light-tight, reflective optical chamber. The detectors are located

below the sample changer at the rear of the instrument.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды