PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 215

Страница: 215 / 218

THEORY

PerkinElmer Life and Analytical Sciences

205

Operational Considerations

The operating procedures for the Tri-Carb 3170TR/SL liquid scintillation analyzer

are described in the appropriate areas of this documentation. Aside from the

count rate limitations and differences in the SNC/IPA procedures, operation of the

Model 3170TR/SL analyzer is exactly the same as other Tri-Carb 3100 analyzers.

The selection of counting vials for low level counting is very important to assure

low background and high sample counting sensitivity. Low potassium glass vials
are recommended when counting low levels of

H or

C. Certain plastic vials may

also be used for large or small samples measuring

H in water.

It is recommended that all glass or plastic vials used for low level counting be

carefully sealed. Teflon cap liners for the screw caps of the vials improve the seal

against leakage.

Glass vials should be washed, then rinsed in a dilute ethylene-diamine-tetraacetic

acid (EDTA) solution, followed by a “dead’’ deionized water rinse and allowed to

air dry. This will help reduce background and further reduce surface contaminants

which could contaminate the detector guard.

Maximum vial dimensions are as follows: small vials must not exceed 17.8mm

diameter and 58.0mm height (including cap); large vials must not exceed 28.1mm

diameter and 63.0mm height (including cap).

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды