PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 87

Страница: 87 / 218

ASSAYS

PerkinElmer Life and Analytical Sciences

SPC Assay

A Single Photon Counting Assay is an assay which measures the photons emitted

from non-radioactive, luminescent samples. To detect scintillation, modern Liquid

Scintillation Counters use two photomultiplier Tubes (PMTs) to collect virtually all

of the light produced within a sample vial. Each pulse that occurs during the

sample counting time is registered and expressed as Counts Per Minute (CPM).

Events are considered true decay events from the sample if they occur within a

specified coincidence time. If these events do not occur in coincidence, they are

considered random (background) and are not counted.

In an SPC Assay, only one PMT is used. As a result, coincidence cannot be used as

a means of excluding background. Therefore, it is often important to reduce the

instrument background to its lowest possible level. Lowering the high voltage

supplied to the photomultiplier tube typically decreases background and increases

sensitivity in SPC Assays.

Performing an SPC Assay

The following tasks are required when performing an SPC Assay.

Calibrate the instrument, if necessary.

Create a new assay choosing SPC as the assay type and define the new assay
parameters.

Associate (link) the assay parameters with a protocol and attach the

corresponding protocol flag to the first cassette to be counted.

Load the cassette(s) with vials and load the instrument with cassettes.

Start the instrument.

Open an existing SPC assay and edit or review if necessary. Save the assay

in the Assays folder of the Packard\TriCarb directory.

Associate (link) the assay parameters with a protocol and attach the
corresponding protocol flag to the first cassette to be counted.

Load the cassette(s) with vials and load the instrument with cassettes.

Start the instrument.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды