PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 173

Страница: 173 / 218

MAINTENANCE

AND

TROUBLESHOOTING

PerkinElmer Life and Analytical Sciences

163

Chapter 9

Maintenance and Troubleshooting

Preventative Maintenance

With the exception of inspection and cleaning, there are no preventative

maintenance procedures that you should perform. Normal system preventative

maintenance can be performed on a prescribed basis under a PerkinElmer

Maintenance Agreement. Contact your PerkinElmer district office or official

PerkinElmer distributor for information concerning the availability of a

maintenance agreement.

Inspection

The following should be inspected on the TriCarb system at least once per week

or whenever a system malfunction occurs:

1. Check that the cassettes and sample changer surfaces are free of dirt.
2. Cassette movement should be smooth with no excessive vibration.
3. Check for loose electrical or mechanical connectors. DO NOT PERFORM ANY

DISASSEMBLY.

4. Ensure that all controls and indicators are working.

Cleaning

The sample changer lid should be cleaned occasionally using a soft cloth

moistened with a mild soap and water solution. The system sample changer

should be cleaned occasionally using a soft cloth moistened with PicoClean-N

(PerkinElmer Life and Analytical Sciences, PPN:6013814) or an appropriate

commercial cleaning agent.

If the system has the refrigerated sample changer option installed, check

(monthly) that the filter is free of dust and dirt, and clean the filter as required.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды