PerkinElmer QuantaSmart 1694267 Скачать руководство пользователя страница 161

Страница: 161 / 218

ADVANCED FEATURES

PerkinElmer Life and Analytical Sciences

151

Low Level Preview

The Low Level Preview function is a Sample Priostat option available via the Run

menu. This feature allows you to observe the sample spectrum and approximate

the count rate of a sample using Low Level count mode.

Figure 8-9 Sample Priostat Window

To preview sample counting using the Low Level Preview feature, you will need to

perform the following tasks:

1. Load your sample(s) into a cassette. Attach the Priostat flag in the reset

position to the cassette.

2. Select Low Level Preview from the Run menu. The Sample Priostat window is

displayed.

3. Select Count from the Run menu. Sample counting will commence immediately

after the instrument identifies the Priostat flag.

4. Stop the counting of a sample by selecting Stop from the Run menu.
5. Select Next Sample followed by Count from the Run menu if you would like to

count additional samples.

6. Stop the sample counting procedure by selecting End Sample Priostat from the

Run menu.

Содержание QuantaSmart 1694267



























































































































































































































Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer QuantaSmart 1694267, Справочное руководство

Результаты поиска

Содержание QuantaSmart 1694267

Отзывы:

Бренды по названию

Популярные бренды