PerkinElmer OilExpress System Скачать руководство пользователя страница 74

Страница: 74 / 102

74 . OilExpress System User's Guide

Sample Preparation

Filtering the Oil

It is important that all oil samples are filtered to prevent large particles blocking the flowcell,

however, care should be taken not to remove any soot particles. A steel mesh filter

(90 microns) is recommended.

Sample Presentation Requirements

Carefully record details of the oil contained in each bottle. Place the sample bottles in the

sample rack, ensuring that the lids have been removed.

The OilExpress System bottle rack accepts standard 4 oz oil sampling bottles. If a smaller

diameter bottle is used ensure that it is centered in the sample holder.

NOTE: For information on how to use the OilExpress System, see the help system available

from the Help menu in the OilExpress software, which includes a tutorial and full

information on using the software.

Содержание OilExpress System







































































































Результаты поиска

Содержание OilExpress System

Отзывы:

Похожие инструкции для OilExpress System

Бренды по названию

Популярные бренды

PerkinElmer OilExpress System, Руководство пользователя

Результаты поиска

Содержание OilExpress System

Отзывы:

Похожие инструкции для OilExpress System

Бренды по названию

Популярные бренды