PerkinElmer OilExpress System Скачать руководство пользователя страница 11

Страница: 11 / 102

Introduction . 11

A Guided Tour of the OilExpress System

Figure 1 The OilExpress System

The PerkinElmer OilExpress System (Figure 1) is a bench-top instrument that provides all the

following in one self-contained unit:

•

A spectrometer, fitted with a sample shuttle.

NOTE: The spectrometer may be a Frontier IR System, Spectrum 100 or 400 Series, or

Spectrum One instrument. For full details on how to install and use your

spectrometer, refer to the documentation supplied with your instrument.

•

A Liquid Autosampler designed to analyze up to 60 samples an hour.

•

A water-resistant flowcell.

The system is controlled by dedicated oil analysis OilExpress software resident on a PC.

NOTE: See the help system available from the

Help

menu in the OilExpress software, which

includes a tutorial and full information on using the software.

Содержание OilExpress System







































































































Результаты поиска

Содержание OilExpress System

Отзывы:

Похожие инструкции для OilExpress System

Бренды по названию

Популярные бренды

PerkinElmer OilExpress System, Руководство пользователя

Результаты поиска

Содержание OilExpress System

Отзывы:

Похожие инструкции для OilExpress System

Бренды по названию

Популярные бренды