PerkinElmer OilExpress System Скачать руководство пользователя страница 65

Страница: 65 / 102

Unpacking and Installation . 65

15.

Right-mouse click within the worktable area of the Autosampler Utilities dialog and from

the menu select

Save Worktable

NOTE: The worktable changes are not automatically saved. If you do not select Save

Worktable, the changes will be lost.

NOTE: The procedure described above must be repeated for all worktables used by the

OilExpress software as anchor points are not applied universally. Follow steps 16 to

20 to calibrate all additional worktables.

16.

Right-mouse click within the worktable area of the Autosampler Utilities dialog and from

the menu select

Load Existing Worktable

17.

Select the required worktable,

PerkinElmer BOTTLES

PerkinElmer VIALS

18.

Repeat steps 4 to 7.

19.

Enter the values you previously recorded in your laboratory notebook into the

and

fields of the User-defined Rack Properties dialog.

Содержание OilExpress System







































































































Результаты поиска

Содержание OilExpress System

Отзывы:

Похожие инструкции для OilExpress System

Бренды по названию

Популярные бренды

PerkinElmer OilExpress System, Руководство пользователя

Результаты поиска

Содержание OilExpress System

Отзывы:

Похожие инструкции для OilExpress System

Бренды по названию

Популярные бренды