PerkinElmer OilExpress System Скачать руководство пользователя страница 49

Страница: 49 / 102

Unpacking and Installation . 49

Installing the Flowcell in the Sample Shuttle

WARNING

DO NOT use the OilExpress System when the sample compartment lid is

fitted. Flammable vapor may seep through instrument seals and gaskets

and accumulate under the lid, where it could cause a fire or explosion

hazard.

Unpack the flowcell.

Slide the flowcell into the sample shuttle (Figure 24).

Make sure that the tubing cannot obstruct the optical beampath.

Figure 24 Sample shuttle accessory and flowcell fitted

Waste Container

We recommend that you use a waste container that is larger than the solvent bottle. Then, if

you empty the waste container whenever you refill the solvent bottle, the waste container

will not overflow.

The waste drains into the container by gravity, so the container should stand on a surface

that is at least 90 cm below the bench on which the OilExpress System is located.

Fitting waste tubing

Attach the waste tubing to the hose connector at the rear of the transfer/wash port.

Insert the waste tubing into the hole on the rear right-hand side of the base plate of the

Autosampler.

Adjust the routing of the tubing so that it is not kinked.

Place the other end of the waste tubing in the waste container.
Ensure that the end will not be immersed in the waste.

CAUTION

Make sure that the ends of the tubing do not become immersed in the

waste or the operation of the analyzer will be impaired.

Содержание OilExpress System







































































































Результаты поиска

Содержание OilExpress System

Отзывы:

Похожие инструкции для OilExpress System

Бренды по названию

Популярные бренды

PerkinElmer OilExpress System, Руководство пользователя

Результаты поиска

Содержание OilExpress System

Отзывы:

Похожие инструкции для OilExpress System

Бренды по названию

Популярные бренды