Panasonic S-LINK V Скачать руководство пользователя страница 9

Страница: 9 / 182

Before Using This System

Instruction for Use

Instructions for Installation

●

Select a power supply unit equipped with the short-circuit protective function (fuse, etc.).

●

The power of the

S-LINK V

system passes through the inside of each unit and is then supplied to

the main cable or I/O device side. However, the short-circuit protective function is not adopted for

this power supply circuit. For this reason, adopt a short-circuit protective function, such as a fuse,

for the power supply circuit.

●

Take care that wrong wiring will damage the product.

●

Before starting the following works, be sure to turn off the power of the PLC (programmable logic

controller), personal computer main body,

S-LINK V

units, and also turn off the power supply unit

of the I/O device.

• Machine assembly (installation)

• Removal or reinstallation of a

S-LINK V

unit or connection of I/O device

• Cable connection

• Address setting / change

●

Before handling this product, remove any electrostatic charge that may be present on your body.

There is a danger of this product getting damaged due to the electrostatic charge.

CAUTION

Hook-up cable connectors

To hook-up an exclusive cable connector, use the exclusive tool, and correctly hook-up the connector by follow-

ing the procedure specified in this manual.

If a connector is not correctly hooked-up, the

S-LINK V

system will not operate.

In addition, observe the following items:

●

After checking the cable type and the purpose, select the right type of connector.

●

Before hook-up a connector, be sure to check the colors of cables to be connected.

●

Use the exclusive hook-up pliers (

SL-JPS

SL-JPC

SL-JPE

) to hook-up the connectors.

For the hook-up procedure of each connector, refer to pages 37 to 44.

●

If a connector is once hooked-up, do not reuse the connector.

The performance of such a connector may be deteriorated.

Wiring

Observe the following items to distribute cables:

●

Keep cables away from the power line and the high-voltage line.

●

Do not completely fold down any cables.

●

Do not pull any cables with a strong force.

●

Do not apply any weight to any cable.

●

Do not touch a cable to any other system cables.

This is because signals of different systems may interfere with each other.

●

Do not bend cables many times.

●

Wind insulation tape on the end of each cable, if necessary.

Others

● Apply the specified torque to tighten terminal screws of each unit.

●

Check the connectors for looseness.

●

Do not disassemble or modify this product.

Instructions for Disposal

●

Request a waste disposal company to dispose of this product.

Содержание S-LINK V























































































































































































Результаты поиска

Содержание S-LINK V

Отзывы:

Бренды по названию

Популярные бренды

Panasonic S-LINK V, Руководство пользователя

Результаты поиска

Содержание S-LINK V

Отзывы:

Бренды по названию

Популярные бренды