Panasonic PT-REQ12 Series, Руководство по эксплуатации

Страница: 14 / 306

14 - ENGLISH
Read this first!
WARNING:
r
POWER
The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible
when problems occur. If the following problems occur, cut off the power supply immediately.
Continued use of the projector in these conditions will result in fire or electric shock, or will cause visual
impairment.
f
If foreign objects or water get inside the projector, cut off the power supply.
f
If the projector is dropped or the cabinet is broken, cut off the power supply.
f
If you notice smoke, strange smells or noise coming from the projector, cut off the power supply.
Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the projector or the cable.
Electric shocks can result.
Do not do anything that might damage the power cord or the power plug.
If the power cord is used while damaged, electric shocks, short-circuits or fire will result.
f
Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it
excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.
Do not use anything other than the provided power cord.
Failure to observe this will result in electric shocks or fire. Please note that if you do not use the provided power
cord to ground the device on the side of the outlet, this may result in electric shocks.
Completely insert the power plug into the wall outlet and the power connector into the projector terminal.
If the plug is not inserted correctly, electric shocks or overheating will result.
f
Do not use plugs which are damaged or wall outlets which are coming loose from the wall.
Do not handle the power plug and power connector with wet hands.
Failure to observe this will result in electric shocks.
Use an outlet supporting 15 A independently.
Using an outlet together with another device may result in fires due to heat generation.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too many adapters), overheating may occur and fire will result.
Clean the power plug regularly to prevent it from becoming covered in dust.
Failure to observe this will cause a fire.
f
If dust builds up on the power plug, the resulting humidity can damage the insulation.
f
If not using the projector for an extended period of time, pull the power plug out from the wall outlet.
Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.
r
ON USE/INSTALLATION
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, fire or damage to the projector.
Do not set up the projector in humid or dusty places or in places where the projector may come into
contact with oily smoke or steam.
Using the projector under such conditions will result in fire, electric shocks or deterioration of components. Oil
may also distort the plastic and the projector could fall such as when mounted on the ceiling.
Do not install this projector in a place which is not strong enough to take the full weight of the projector
or on top of a surface which is sloped or unstable.
Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage
could result.
Do not install the projector in a location where people pass through.
People may bump into the projector or trip on the power cord, which may result in fire, electric shock, or injury.
Install the projector in a location sufficiently away from surrounding walls and objects so that air
ventilation is not obstructed.
Failure to observe this will cause the projector to overheat, which can cause fire or damage to the projector.
f
Do not place the projector in narrow, badly ventilated places.
For details, refer to “Cautions when setting up the projector” (
x
page 26).
f
Do not place the projector on cloth or papers, as these materials could be drawn into the intake vent.