manualshive.com logo in svg

Panasonic MN103001G/F01K, Руководство пользователя

Поделиться
Скачать
Panasonic MN103001G/F01K Скачать руководство пользователя страница 363

A/D Converter

14-9

(3) Any one channel/continuous conversion

If "any one channel/continuous conversion" is selected as the operating mode (ADMD1 to 0), one AN input

is converted continuously.  Set the conversion channel in the conversion channel selection bits (ADSC1 to 0).

(ADMC1 to 0 are ignored.)  An A/D interrupt request is generated each time conversion is completed.

When starting up conversion through software, set the conversion start trigger selection bits (ADST1 to 0) to

"00", and set the conversion start/execution flag (ADEN) to "1".

If the conversion start trigger selection bits (ADST1 to 0) are set to "external trigger," then the conversion

start/execution flag (ADEN) is set to "1" when a falling edge is input to the ADTRG pin, A/D conversion then
starts.

And if the conversion start trigger selection bits (ADST1 to 0) are set to "timer trigger," then the conversion

start/execution flag (ADEN) is set to "1" when a timer 2 underflow occurs, A/D conversion then starts.

The conversion start/execution flag (ADEN) is "1" while conversion is in progress, and is not cleared by

hardware.  Therefore, set the conversion start/execution flag (ADEN) to "0" when stopping the conversion operation.

Fig. 14-5-3   External Trigger Input Conversion Example

Clear by software when stopping 
the conversion operation.

Set

N channel 

conversion

N channel 

conversion

N channel 

conversion

N channel 

conversion

N channel 

conversion

External trigger input 

(ADTRG pin)

ADEN flag

Interrupt request

Status

Содержание MN103001G/F01K



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды