manualshive.com logo in svg

Panasonic MN103001G/F01K, Руководство пользователя

Поделиться
Скачать
Panasonic MN103001G/F01K Скачать руководство пользователя страница 301

Watchdog Timer

12-9

Watchdog operation

If the WDCNE flag is set to "1" and the watchdog operation is enabled, a non-maskable interrupt is generated if a
watchdog timer overflow occurs.

When an overflow occurs, the watchdog timer overflow output is output to the WDOVF flag.  Pulse output or level
output can be selected through the WDOVT flag. When level output is selected, the watchdog timer overflow
output (WDOVF flag) is cleared by writing a "1" to the WDRST flag or by reset (RST) pin "L" level  input.

Fig. 12-5-3   Operation Diagram 3: Watchdog Operation

Before setting the WDCNE flag to "1", write a "1" to the WDRST flag to reset the counter.

When switching to HALT or SLEEP mode, set the WDCNE flag to "0" to turn off the watchdog timer.

Self-reset operation

The chip resets internally when a "1" is written to the CHIPRST bit in the RSTCTR register.  The oscillation
stabilization wait operation is not performed.

The reset generated by writing the CHIPRST flag is an internal reset signal within the chip and does not manifest

itself on the external reset pin (RST pin).

Watchdog timer 

count value

Overflow

4.369 ms to 1118.481 ms

(when CKSEL = “H” and the oscillating input 

frequency is 15 MHz)

Counter reset by writing 

“1” to the WDRST flag

Non-maskable interrupt

WDOVF flag output  

(when pulse output is 

selected)

WDOVF flag output 

(when level output is 

selected)

SYSCLK 255-cycle width

Reset by writing a “1” 
to the WDRST flag, or 
by reset pin input

Содержание MN103001G/F01K



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды