Omron XPECTIA FZ3 Скачать руководство пользователя страница 157 | Manualshive

Страница: 157 / 440

Omron XPECTIA FZ3 Скачать руководство пользователя страница 157

2

Measurement

FZ3 Processing Items List Manual

Color Data

155

List of Color Data Items

Item name

Description

Region
setting

This item is used to set up the measurement area.
While the input image can be measured as a whole, a quick and reliable measurement can be
performed by set up the measured range.
Reference:

Region Setting (Color Data) (p.155)

Measurement

This item specifies the judgement condition for measurement results.

●

For color cameras:

Set the average color (RGB) value and deviation and set what the maximum difference is for
judging the object to be OK.

●

For monochrome cameras:

Specify the average density value and deviation and set what the maximum difference is for
judging the object to be OK.

Measurement parameter can be changed as needed to address unstable measurement results or to
increase the processing speed.Normally, the factory default value will be used.
Reference:

Measurement Parameters (Color Data) (p.156)

Output
parameter

This item can be changed if necessary.Normally, the factory default value will be used.
Specify whether to reflect the judgement result to the overall judgement of the scene.
Reference:

Output Parameters (Color Data) (p.158)

Region Setting (Color Data)

This item is used to set up the measurement area.It is possible to measure the entire input image, but
restricting the range enables accurate measurement in a short period of time.
A measurement region for [Color Data] can be specified as a rectangle, circle (ellipse), circumference, or
polygon.

Note

●

Up to 8 graphs can be used together to draw the measured region.Complex areas can be drawn through image

integration or by removing unnecessary sections from the measurement region.

1.

In the Item Tab area, tap [Region setting].

2.

Select a button in the drawing tools.

3.

In the figure setting area, specify a region to be measured.

4.

In the figure setting area, tap [OK].

The measurement region is registered and displayed in the Image Display area.

Acesst 1.0 6251194

«
...
155
156
157
158
159
...
»

Содержание XPECTIA FZ3

























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды