![background image](http://html1.mh-extra.com/html/omron/ns15-v2-series/ns15-v2-series_setup-manual_743134043.webp)
2-2 Part Names and Functions
2-9
NS15 Rear Panel Switches
Serial Port B Connector
(Isolated RS-422A)
Use the RS-422A connector
provided with the PT.
Serial Port B DIP Switch
Selects the type of communications for
serial port B and RS-422A
communications conditions.
Expansion Interface Connector
Used to mount the Video Input Unit or
the Controller Link Interface Unit.
Memory Card Connector
Used to connect the memory
card for storing and transmitting
screen data, log data, and
system programs.
DIP Switch
Used to set the settings for
transmitting data using the
Memory Card.
Reset Switch
Used to initialize the PT. The
status of screen data, other
registered data, and the system
menu, however, will not change.
Battery Cover
The battery is installed
underneath the cover.
Analog RGB Output Connector
Connects to the monitor.
Memory Card Power Indicator
Indicates the status of power to
the Memory Card.
Serial Port A Connector
Used to connect the host, CX-Designer, and Bar Code Reader.
Uses an RS-232C 9-pin connector.
Serial Port B Connector (RS-232C)
Connects to a host, CX-Designer, or Bar Code
Reader using an RS-232C 9-pin connector.
Power Input Terminal
Block Cover
Covers the power input
terminal block.
External Brightness Adjustment
Connector
Connects to an external variable
resistor to adjust the brightness of
the touch panel.
USB Slave Connector
This is a USB Type B connector. It can be used to connect to the CX-Designer.
Refer to
3-3-2 Connecting via USB.
A PictBridge-compatible printer can also be connected.
(Refer to
3-5-2 Connecting a PictBridge-compatible Printer
.)
USB Host Connector
Used to connect to printers.
It is a USB Type A connector.
Refer to
3-5-1 Connecting to a Printer
Compatible with ESC/P Raster or BJ Raster.
FG Terminal
Used to prevent malfunctions
due to noise interference.
Main Circuit DC
Input Terminals Used to
connect the power supply.
Ethernet Connector
Used to connect the Ethernet cable.
Uses a 10Base-T/100Base-T 8-pin modular plug.
*: The NS-CLK21 can be used.
The NS-CA001 cannot be used.
The NS-CA002 can be used for analog RGB input, but not for video input.
Precautions
for Safe Use
Confirm system safety before turning the power ON/OFF or restarting. Other-
wise the system may operate unpredictably.
Precautions
for Correct Use
•
There are two connectors that can be used for serial port B, an isolated RS-
422A connector and an RS-232C connector. They cannot be used at the
same time. Set the DIP switch pins for the serial port B setting to specify the
port that is to be used.
•
When using RS-422A communications, use the RS-422A connector in-
cluded with the PT for the isolated RS-422A serial port B connector.
Содержание NS15-V2 Series
