Oki Data CONFIDENTIAL
45850101TH Rev.1
2-37
2. TROUBLESHOOTING PROCEDURES
No. Value
(Hex)
Description
Solution
24.
45
Phase-B Command Rec Error (Failed to
receive a control signal at the time of receiving)
(Including SEP discrepancy in bulletin board
polling receiving)
Set to 'OFF' the setting of 'Super G3'.
Otherwise, the transmission state is poor
quality.
Wait a few minutes, and retry faxing.
Or, enquire to the instituting dealer for
the telephone line.
25.
46
Phase-B Response Rec Error
(Failed to receive a control signal at the time
of sending ) (Including SUB discrepancy in
confidential sending)
Set to 'OFF' the setting of 'Super G3'.
Otherwise, the transmission state is poor
quality.
Wait a few minutes, and retry faxing.
Or, enquire to the instituting dealer for
the telephone line.
26.
47
Phase-B Invalid Command/Response Rx
(Received an invalid signal.)
In possibly, the other side fax no
response.
Wait a few minutes, and retya faxing.
Otherwise, enquire to the other side.
27.
48
A machine on the other end was incapable of
receiving.
In possibly, the other side fax no
response.
Wait a few minutes, and retya faxing.
Otherwise, enquire to the other side.
28.
49
T1 timeout after EOM
(T1 timeout after EOM receiving)
This side fax could not receive the signal
of the sending side fax in specified term.
Require of to resend the fax by the other
side.
Otherwise, in the case of connecting
through IP-circuit, Set to off for the
setting of the Super-G3.
* setting changing process
Set to 'OFF' for the category of [Device
Settings]-[Admin Setup]-[User Install]-
[Super G3].
29.
4A
Invalid CSI error (Dialing numbers didn't match
with ID of the machin on the other end in
confirmation sending.)
Abort the fax sending (error occured) by
the function of the ID check sending.
The fax number is defferent the information
of the own registered phone number in the
other side fax from the inputed destination
fax number at this side fax.
Send after change the setting to 'OFF' of
the ID confirmation sending.
Otherwise, require to the other side as
to correct the information of the own
registered phone number in the other side
fax.
* setting changing process
Set to 'OFF' for the category of [Device
Setting]-[Admin Setup]-[Fax Setup]-
[Sequrity Function]-[ID Check Tx].
No. Value
(Hex)
Description
Solution
30.
4B
Invalid TSI error (matches number denied
acceptance registered as nuisance fax)
Rejected receving by the function of the
Block Junk Fax as nuisance
fax.
The destination information is not
matched between the information of the
own registered phone number in the
other side fax from the information of the
registered other side's phone number at
this side fax.
Otherwise, the information is matched
with registered nuisance fax number in
the registered list.
---
In the case of allowing to receive the fax,
set to any of following measure.
In case of 'Mode 1' is the function mode:
implement
①
or
②
.
In case of 'Mode 2' is the function mode:
implement
①
or
③
.
In case of 'Mode 3' is the function mode:
implement
①
or
②
and
③
.
①
: Set to 'OFF' the function of theBlock
Junk Fax .
②
: Register the fax number allowed to
receive to 'Speed Dialing'.
③
: Delete the fax number allowed to
receive from 'Registered List'.
* setting changing process
Set to 'OFF' for the category of [Device
Setting]-[Admin Setup]-[Fax Setup]-
[Other Settings]-[Block Junk Fax].
31.
4c
FIF:bit49 of a facing machine's DIS was 0 in
confidential sending (A facing machine was
incapable of confidential receiving).
The other side's fax is not arranged the
confidential communication system with
F-Cord.
Check the confidential receiving box
opened and to available in confidential
receiving at other side's fax.
32.
4d
FIF:bit47 of a facing machine's DIS was 0
in bulletin board polling receiving (A facing
machine was incapable of bulletin board
polling sending).
The other side's fax is not arranged the
bulletin board communication system
with F-Cord.
Check the bulletin board box opened
and to available in bulletin board polling
sending by F-Cord at other side's fax.
