manualshive.com logo in svg

NXP Semiconductors MPC5644A, Справочное руководство, Страница: 818 / 1735

Поделиться
Скачать
NXP Semiconductors MPC5644A Скачать руководство пользователя страница 818

Enhanced Time Processing Unit (eTPU2)

MPC5644A Microcontroller Reference Manual, Rev. 6

818

Freescale Semiconductor

 

24.5.1.2

Time slot transition

The Time Slot Transition period (also called TST for short) is the interval between the servicing of two 
channels, during which all Channel-specific context is loaded for the new serviced Channel. The primary 
tasks completed during this period include:

•

Set MEF for the first microcycle plus eventual wait-states.

•

Reset the MEF for one microcycle after the first microcycle plus wait-states.

•

Update of the CHAN register with the number of the new channel to be serviced.

•

Parallel update of ERTA and ERTB from CaptureA and CaptureB registers of the new serviced 
channel.

•

Sampling of the branch conditions of the new channel to be serviced into the branch logic (this 
means flags TDLA/B, MRLA/B, LSR, FM[1], FM[0], and PSS). The branch conditions are 
coherent with the timebase capture values sampled into ERTA/B (if MRLA/B, TDLA/B are set at 
the same time of the sampling, either both old flag state and capture values are sampled, or both 
new values are sampled).

•

Formation of the entry point address.

•

Copy the ME bit in the Entry Point into MEF.

•

Access to the entry point location and getting the first microinstruction address.

14

ME

Match Enable
ME specifies whether match event recognitions are enabled or disabled for the thread associated with the 
entry point during the thread execution. If they are disabled, a match recognition can only occur after 
channel service. For more details refer to 

Section 24.5.5.2, Match Recognition

.

Matches are disabled during the thread.
Matches are enabled during the thread.
The disabling of Match A/B recognition by MEF is dependent on IPACA/B configuration on the serviced 
channel (see 

Section 24.5.5.1.2, Pin Control Registers

). If IPACA = 1xx, Match A is not disabled by 

ME = 0. Likewise, IPACB = 1xx overrides the effect of ME on Match B to “always on” If IPACA/B = 0xx, 
Match A/B is disabled for one microcycle during TST (see 

Section 24.5.1.2, Time slot transition

) and is 

re-enabled when Entry Point is loaded, if ME = 1. Note that if the comparator is in equal-only mode and 
the time base reaches the value of the Match register during the time that recognition is disabled 
(beginning of TST, plus whole thread if ME = 0), the match recognition is lost. If the comparator is in 
greater-equal mode, the match event may be recognized after the disabling period if it satisfies the 
“greater-than” condition.

15

PP

Preload Parameter
PP indicates which pair of channel parameters are loaded into registers P and DIOB from the SPRAM prior 
to the execution of a thread. Preloading occurs during the time-slot transition period (see 

Section 24.5.1.2, 

Time slot transition

)

Microengine register P is preloaded from parameter 0 and DIOB from parameter 1.
Microengine register P is preloaded from parameter 2 and DIOB from parameter 3.
The parameter numbers are offsets from the channel parameter base address. For more info, see 

Section 24.5.2.3, Parameter access

.

Field

Description

Содержание MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов