manualshive.com logo in svg

NXP Semiconductors MPC5644A, Справочное руководство, Страница: 1102 / 1735

Поделиться
Скачать
NXP Semiconductors MPC5644A Скачать руководство пользователя страница 1102

Enhanced Queued Analog-to-Digital Converter (EQADC)

MPC5644A Microcontroller Reference Manual, Rev. 6

1102

Freescale Semiconductor

 

This feature is necessary when the timing of some conversion is very important. In normal priority scheme, 
when CFIFO0 is triggered, its conversion command can be put behind 2 pending conversion commands 
in the Cbuffer due to the queue structure. Considering that these 2 pending commands are from lower 
priority CFIFOs and that the delay between the trigger and the sampling of the command from CFIFO0 
can be unacceptable, EQADC can be configured to permit immediate conversion commands from CFIFO0 
with abort function.

When CFIFO0 is triggered and abort is enabled, up to 2 commands in Cbuffer0 or Cbuffer1 are stored in 
a side register. The abort request signal is generated to ADC0 or ADC1 and the confirmation of ADC 
reset/ready is waited to send the command from CFIFO0 to the decoded Cbuffer.

After the transfer of all commands from CFIFO0, the recovery phase restores the up to 2 commands that 
were in Cbuffer when the abort occurred. After this recovery phase, it is established the normal process of 
prioritization of commands from CFIFOs.

25.6.4.5

External Trigger Event Detection

The digital filters for trigger signals can be individually bypassed by asserting the input control signals 
eqadc_intern_trig_sel5-0. When the filter is bypassed, the ETRIG input signal is not filtered and the logic 
after the filter receives a copy of this input trigger signal.

The Digital Filter Length field in 

Section 25.5.2.4, EQADC External Trigger Digital Filter Register 

(EQADC_ETDFR)

, specifies the minimum number of system clocks that the ETRIG0-5 signals must be 

held at a logic level to be recognized as valid. All ETRIG signals are filtered. A counter for each queue 
trigger is implemented to detect a transition between logic levels. The counter counts at the system clock 
rate. The corresponding counter is cleared and restarted each time the signal transitions between logic 
levels. When the corresponding counter matches the value specified by the Digital Filter Length field in 

Section 25.5.2.4, EQADC External Trigger Digital Filter Register (EQADC_ETDFR)

, the EQADC 

considers the ETRIG logic level to be valid and passes that new logic level to the rest of the EQADC.

The filter is only for filtering the ETRIG signal. Logic after the filter checks for transitions between filtered 
values, such as for detecting the transition from a filtered logic level zero to a filter logic level one in rising 
edge external trigger mode. The EQADC can detect rising edge, falling edge, or level gated external 
triggers. The digital filter will always be active independently of the status of the MODE

x

 field in 

Section 25.5.2.7, EQADC CFIFO Control Registers (EQADC_CFCR)

, but the edge, level detection logic 

is only active when MODEx is set to a value different from disabled, and in case MODEx is set to single 
scan mode, when the SSS bit is asserted. Note that the time necessary for a external trigger event to result 
into a CFIFO status change is not solely determined by the DFL field in the 

Section 25.5.2.4, EQADC 

External Trigger Digital Filter Register (EQADC_ETDFR)

. After being synchronized to the system clock 

and filtered, a trigger event is checked against the CFIFO trigger mode. Only then, after a valid trigger 
event is detected, the EQADC accordingly changes the CFIFO status. Refer to 

Figure 25-66

 for an 

example.

Содержание MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов