Nortel 1002rp Скачать руководство пользователя страница 47

Страница: 47 / 218

January 2007

Using Windows online diagnostic tools

1002rp Server Maintenance and Diagnostics

The netstat command

The netstat command displays current TCP/IP network connections and
protocol statistics.

Netstat command syntax

The netstat command uses the following syntax:

netstat [-a] [-e] [-n] [-s] [-p proto] [-r] [interval]

netstat command parameters

Table 7: netstat command parameters

To run the netstat command from Windows

Click Start

➝

Programs

➝

Accessories

➝

Command Prompt.

Result:

The Command Prompt window appears.

At the Command prompt, type

netstat

with the required

parameters.

Parameter

Description

-a

Displays all connections and listening ports.

-e

Displays Ethernet statistics. This can be combined with
the -s option.

-n

Displays addresses and port numbers in numeric form.

-s

Displays statistics for each protocol.

-p proto

Shows connections for the protocol specified by proto.
Proto can be TCP or UDP. If used with the -s option,
proto can be TCP, UDP, or IP.

-r

Displays the contents of the routing table.

interval

Redisplays selected statistics, pausing between each
display. Press Ctrl+C to stop redisplaying.

Содержание 1002rp



























































































































































































































Результаты поиска

Содержание 1002rp

Отзывы:

Бренды по названию

Популярные бренды

Nortel 1002rp, Техническое обслуживание и диагностика

Результаты поиска

Содержание 1002rp

Отзывы:

Бренды по названию

Популярные бренды