manualshive.com logo in svg

Nortel 1002rp, Техническое обслуживание и диагностика

Поделиться
Скачать
Nortel 1002rp Скачать руководство пользователя страница 110

Replacing basic chassis components

Standard 1.11

110

CallPilot

Removing the front bezel and server cover

If the maintenance task requires replacing front panel components, you 
must remove the front bezel. The exception is the hard drives, which can 
be accessed by simply unlocking and opening the front bezel doors.

If you require access to the server interior, remove both the front bezel 
and the server cover.

Requirements

Before you remove the front bezel and server cover, gather the following 
tools:

„

the customer’s chassis keys for the front bezel doors

„

a flat-blade screwdriver

„

an antistatic wrist strap

About the front bezel doors

Two locked doors on the front of the server cover the front panel, 
including the CD-ROM drive and tape drive. 

These doors are part of the front bezel. You must unlock the front panel 
doors before you can remove the front bezel. 

Содержание 1002rp



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды