manualshive.com logo in svg

Nortel 1002rp, Техническое обслуживание и диагностика

Поделиться
Скачать
Nortel 1002rp Скачать руководство пользователя страница 159

January 2007

RAID operations

1002rp Server Maintenance and Diagnostics

159

Configuring RAID firmware, driver, and 
power console

Verifying the RAID configuration

There is a direct relationship between the driver, firmware and Power 
Console utility versions used with a RAID card. While mixing driver 
versions with firmware is not critical, mixing Power Console Utility with 
the wrong driver or firmware can lead to system instability and data 
corruption. Table 17 on page 159 shows the accepted and tested 
combinations for Windows 2003

Table 17:RAID driver, firmware, and Power console configuration.

To determine the current RAID firmware version:

1

Launch the MegaRAID client using: Start 

➝

 Programs 

➝

 Power 

Console Plus 

➝

 Launch Client.

2

From the MegaRAID Power Console Plus, Server Selection 
window, select Access Mode

 

➝

 Full Access to view or change 

configuration information and click OK.

3

Select Adapter 

➝

 Properties.

RAID card

Driver

Firmware

MegaRAID 
Power Console

LSI1600

6.45 (6.36 works 
temporarily but must 
be upgraded)

111U

5.00i

LSI320-2

6.45 (6.36 works 
temporarily but must 
be upgraded)

1L37

5.00i

Содержание 1002rp



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды