Nortel 1002rp Скачать руководство пользователя страница 119

Страница: 119 / 218

January 2007

Replacing basic chassis components

1002rp Server Maintenance and Diagnostics

119

Replacing the SCA SCSI drive cage and
fused power cable

Due to the potential of an over-current condition, Nortel provides a
retrofit SCSI power cable kit for the

N0029330

power cable. The kit

comprises an improved SCSI power cable, product label, and retrofit
procedure.

The cable kit part number for all locations, except EMEA, is

FR029367

At EMEA locations, use part number

N0029367

Only qualified field technicians who are familiar with CallPilot and
RAID should attempt this procedure.

A full-system backup and RAID drive consistency check must be
performed prior to replacing the SCSI power cable. These can both
be performed while the server is online.

If at any step in the procedure, the result is not as indicated, stop and
contact your next level of support for assistance before continuing.

To replace the SCSI power cable

Log into the CallPilot server.

Launch the MegaRAID client to check the status of the RAID sub-
system:

Click Start

➝

Programs

➝

Power Console Plus

➝

Launch

Client.

Result:

The Server Selection window appears.

Select Access Mode

➝

Full Access and click OK.

Result:

The MegaRAID Power Console Plus window appears.

Содержание 1002rp



























































































































































































































Результаты поиска

Содержание 1002rp

Отзывы:

Бренды по названию

Популярные бренды

Nortel 1002rp, Техническое обслуживание и диагностика

Результаты поиска

Содержание 1002rp

Отзывы:

Бренды по названию

Популярные бренды