manualshive.com logo in svg

NI PXI-4204, Руководство пользователя

Поделиться
Скачать
NI PXI-4204 Скачать руководство пользователя страница 27

Chapter 3

Using the NI PXI-4204

©

 National Instruments Corporation

3-3

NI PXI-4204 User Manual

Signal Conditioning Functional Overview

The NI PXI-4204 is part of the NI PXI-4200 series of DAQ devices 
designed to provide application-specific signal conditioning, DAQ, and 
integrated field wiring connectivity on the same product. The NI PXI-4204 
signal conditioning circuitry is designed to provide attenuation, 
amplification, filtering, and SS/H capability as described in Table 3-1.

Table 3-1.  

Signal Conditioning Functional Blocks

Signal Conditioning Component

Description

Divide-by-Ten Attenuator

Each NI PXI-4204 channel front end has a balanced 
divide-by-ten attenuator. The attenuation is provided by 
a resistor-divider network that provides 1 M

Ω 

input 

impedance. The balanced attenuator followed by an 
instrumentation amplifier provides rejection of 
common-mode signals and enables the NI PXI-4204 to 
measure voltages up to ±100 V.

Input Multiplexer

Each channel of the NI PXI-4204 includes an analog 
multiplexer. You can use this multiplexer to 
programmatically route internal test signals to the 
NI PXI-4204 instrumentation amplifiers for self-calibration 
and self-test.

Instrumentation Amplifier

The instrumentation amplifier following the attenuation stage 
of the NI PXI-4204 provides a very high-load impedance to 
the previous stage, rejection of common-mode signals, and 
converts differential signals to single-ended signals that are 
then fed to the filter stage.

Содержание PXI-4204




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды