NetApp E2760 Скачать руководство пользователя страница 34

Страница: 34 / 137

Step 4 - Installing the controller-drive tray

Things to know - General installation

The power supplies meet standard voltage requirements for both domestic and worldwide operation.

Note:

Ensure that the combined power requirements of your trays do not exceed the power

capacity of your cabinet. For power ratings on the and its related drive trays, refer to the

Site

Preparation Guide.

Procedure - Installing the E2712 or E2724 controller-drive
tray

About this task

Warning:

(W08) Risk of bodily injury – Two persons are required to safely lift the component.

Warning:

(W05) Risk of bodily injury – If the bottom half of the cabinet is empty, do not install

components in the top half of the cabinet. If the top half of the cabinet is too heavy for the bottom
half, the cabinet might fall and cause bodily injury. Always install a component in the lowest
available position in the cabinet.

You can install the controller-drive tray into an industry-standard cabinet.

This procedure describes how to install the mounting rails into an industry-standard cabinet.

Attention:

Possible hardware damage – To prevent electrostatic discharge damage to the tray,

use proper antistatic protection when handling tray components.

Steps

1. Ensure that the cabinet is in the final location and the cabinet installation site meets the clearance

requirements for air flow as shown in the figures.

Note:

Fans pull air through the tray from front to back across the drives.

Содержание E2760










































































































































Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды

NetApp E2760, Руководство по установке

Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды