NetApp E2760 Скачать руководство пользователя страница 116

Страница: 116 / 137

Table 22: LEDs on the drive

Location

LED

Color

Blinking

Off

Drive Power

Green

The power is
turned on, and the
drive is operating
normally.

Drive I/O
activity is
taking place.

The power is
turned off.

Drive Service
Action
Required

Amber

An error has
occurred.

Normal status.

Drive Service
Action
Allowed

Blue

The drive canister
can be removed
safely from the
drive tray.

The drive
canister cannot
be removed
safely from the
drive tray.

•

Drive state represented by LEDs

Table 23: Drive state represented by LEDs

Drive state

Drive Power LED
(Green)

Drive Service Action
Required LED (Amber)

Power is not applied.

Off

Normal operation – The power is turned on,
but drive I/O activity is not occurring.

Off

Normal operation – Drive I/O activity is
occurring.

Blinking

Off

Service action required – A fault condition
exists, and the drive is offline.

116 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Содержание E2760










































































































































Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды

NetApp E2760, Руководство по установке

Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды