NetApp E2760 Скачать руководство пользователя страница 113

Страница: 113 / 137

LED

Symbol

Location
(Canisters)

Function

Controller-Drive Tray
Over-Temperature

Front bezel on the
controller-drive
tray

•

On – The temperature of
the drive tray has reached
an unsafe condition.

•

Off – The temperature of
the drive tray is within
operational range.

Standby Power

Front bezel on the
controller-drive
tray

•

On – The controller-drive
tray is in standby mode and
the main DC power is off.

•

Off – The controller-drive
tray is not in standby mode
and the main DC power is
on.

Seven-Segment ID
Diagnostic Display

Controller

The tray ID or a diagnostic
code is indicated.

For example, if some of the
cache memory dual in-line
memory modules (DIMMs)
are missing in a controller,
error code L8 appears in the
diagnostic display (see

Things

to know - Lock-down codes

page 129).

AC power

Power-fan

Note:

The LED

is directly above
or below the AC
power switch
and the AC
power
connector.

Indicates that the power supply
is receiving AC power input.

DC power

Power-fan

Note:

The LED

is directly above
or below the
DC power
switch and the
DC power
connector.

Indicates that the power supply
is receiving DC power input.

Step 10 - Turning on the power and checking for problems in a controller-drive tray configuration | 113

Содержание E2760










































































































































Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды

NetApp E2760, Руководство по установке

Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды