NetApp E2760 Скачать руководство пользователя страница 120

Страница: 120 / 137

Table 26: LEDs on the left bezel

Location

LED

Color

Off

Drive Tray
Power

Green

Power is present.

Power is not present.

Drive Tray
Standby Power

Green

The drive tray is in
Standby Power mode.

The drive tray is not in
Standby Power mode.

Drive Tray
Locate

White

Identifies a drive tray
that you are trying to
find.

Normal status.

Drive Tray
Over-
Temperature

Amber

The temperature of the
drive tray has reached
an unsafe level.

Normal status.

Drive Tray
Service Action
Required

Amber

A component within
the drive tray needs
attention.

Normal status.

•

LEDs on the ESM canister

Table 27: LEDs on the ESM canister

Location

LED

Color

Off

Host Link 1
Fault

Amber

At least one PHY of the
four connectors is
working, but another
PHY cannot establish
the same link to the
device connected to the
Host IN port connector.

No link error has
occurred.

Host Link 1
Active

Green

At least one of the four
PHYs in the In port is
working, and a link
exists to the device
connected to the Host In
connector.

A link error has
occurred.

120 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Содержание E2760










































































































































Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды

NetApp E2760, Руководство по установке

Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды