NetApp E2760 Скачать руководство пользователя страница 66

Страница: 66 / 137

Cabinet mounting holes

Adjustment screws for locking the mounting rail length

Mounting rails

Clip for securing the rear of the drive tray

b. Place the mounting rail inside the cabinet, and extend the mounting rail until the flanges on

the mounting rail touch the inside of the cabinet.

c. Ensure that the alignment spacers on the front flange of the mounting rail fit into the mounting

holes in the cabinet.

The front flange of each mounting rail has two alignment spacers. The alignment spacers are
designed to fit into the mounting holes in the cabinet. The alignment spacers help position and
hold the mounting rail.

Note:

If the cabinet in which you are installing this tray has square holes, there are larger

spacers that can be used to mount the rail.

66 | E2700 Controller-Drive Tray and Related Drive Trays Installation Guide

Содержание E2760










































































































































Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды

NetApp E2760, Руководство по установке

Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды