NetApp E2760 Скачать руководство пользователя страница 39

Страница: 39 / 137

Mounting rail

Clip

Partial view of the controller-drive tray rear sheet metal

Mounting holes

7. Secure the front of the controller-drive tray to the cabinet. Use the two screws to attach the flange

on each side of the front of the controller-drive tray to the mounting rails.

a. Insert one M5 screw through the bottom hole of a flange on the controller-drive tray so that

the screw goes through the cabinet rail and engages the bottom captured nut in the mounting
rail. Tighten the screw.

b. Repeat the step for the second flange.

Note:

The rear of the controller-drive tray contains two controllers. The top of the

controller-drive tray is the side with the labels.

8. Secure the side of the controller-drive tray to the mounting rails by performing these steps:

a. Insert one M4 screw through the side sheet metal of the controller-drive tray into the captured

nut on the side of the mounting rail. Tighten the screw.

b. Repeat the step for the other side.

9. Attach the plastic end caps onto the front of the controller-drive tray.

a. Put the top of the end cap on the hinge tab that is part of the controller-drive tray mounting

flange.

b. Gently press on the bottom of the end cap until it snaps into place over the retainer on the

bottom of the controller-drive tray mounting flange.

Step 4 - Installing the controller-drive tray | 39

Содержание E2760










































































































































Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды

NetApp E2760, Руководство по установке

Результаты поиска

Содержание E2760

Отзывы:

Похожие инструкции для E2760

Бренды по названию

Популярные бренды