NEC VR4181 mPD30181 Скачать руководство пользователя страница 370

Страница: 370 / 444

CHAPTER 19 SERIAL INTERFACE UNIT 1 (SIU1)

User’s Manual U14272EJ3V0UM

370

When transmit FIFO is enabled and transmit interrupts are enabled, transmit interrupt requests can occur as

described below.

1. When the transmit FIFO becomes empty, a transmit holding register empty interrupt request occurs.

This interrupt request is cleared when a character is written to the transmit holding register (from one to

16 characters can be written to the transmit FIFO during servicing of this interrupt), or when the SIUIID_1

2. If there are not at least two bytes of character data in the transmit FIFO between one time when the LSR5

bit = 1 (transmit FIFO is empty) in the SIULS_1 register and the next time when the LSR5 bit = 1, transmit

FIFO empty status is reported to the IIR bits after a delay period calculated as “the time for one character

−

the time for the last stop bit(s)”.

When transmit interrupts are enabled, the first transmit interrupt request that occurs after the FCR0 bit

(FIFO enable bit) in the SIUFC_1 register is overwritten is indicated immediately.

The priority level of the character timeout interrupt and receive FIFO trigger level interrupt is the same as that of

the receive data ready interrupt.

The priority level of the transmit FIFO empty interrupt is the same as that of the transmit holding register empty

interrupt.

Whether data to be transmitted exists or not in the transmit FIFO and the transmit shift register, check the LSR6

bit of the SIULS_1 register. The LSR5 bit of the SIULS_1 register is used to check whether data to be transferred

exists or not in the transmit FIFO only. Therefore, there may be data in the transmit shift register.

•

FIFO polling mode

When the FCR0 bit = 1 (FIFO is enabled) in the SIUFC_1 register, if the value of any or all of the SIUIE_1

are controlled separately, polling mode can be set for either or both blocks.

When in this mode, the status of the transmit block and/or receive block can be checked by reading the SIULS_1

When in the FIFO polling mode, there is no notification when the trigger level is reached or when a timeout

occurs, but the receive FIFO and transmit FIFO can still store characters as they normally do.

Содержание VR4181 mPD30181





























































































































































































































































































































































































































































Результаты поиска

Содержание VR4181 mPD30181

Отзывы:

Похожие инструкции для VR4181 mPD30181

Бренды по названию

Популярные бренды

NEC VR4181 mPD30181, Руководство пользователя

Результаты поиска

Содержание VR4181 mPD30181

Отзывы:

Похожие инструкции для VR4181 mPD30181

Бренды по названию

Популярные бренды