NEC Express5800/R320a-E4 Скачать руководство пользователя страница 53

Страница: 53 / 186

Windows Setup 4-3

SETUP FLOW

Step 1 Start the OS reinstallation setup procedure

Step 2 Prepare the OS reinstallation setup

Step 3 Disable OS Boot Monitoring Function

Set [NEC EXPRESSBUILDER] DVD

Create [OEM-Disk] *1

Specify the size of the partition for OS installation

Prepare for OS (Windows) installation and ft Server
Control Software installation

Set OS (Windows) CD/DVD-ROM

Install driver in [OEM-Disk]

Start the OS installation

Apply [Update the system]

Install ft Server Control Software and

NEC ESMPRO Agent

Set OS (Windows) CD/DVD-ROM

Automatic installation of following software:

OS (Windows)

ft Server Control Software

NEC ESMPRO Agent

Manual Setup

Express Setup

Step 4B Manual Setup

: Entered or selected by the user

: Proceeds automatically

Completion

Step 5 Connect and Configure Options

Step 7 Service Pack Installation

Step 6 Update Software

Step 8 Set Duplex LAN Configuration

Step 9 Set Dual Disk Configuration

Step 10 Create Volume

Step 12 Enable OS Boot Monitoring

Step 13 Make Settings for Failure

Step 14 Back up System Information

This flow chart illustrates the flow of the setup

procedures for the NEC Express5800/R320a-E4/M4.

Step 4A Express Setup

Step 11 Set Network for NEC ESMPRO

*1 Windows Server 2008 does not

require OEM-Disk.

Содержание Express5800/R320a-E4



























































































































































































Результаты поиска

Содержание Express5800/R320a-E4

Отзывы:

Бренды по названию

Популярные бренды

NEC Express5800/R320a-E4, Руководство пользователя

Результаты поиска

Содержание Express5800/R320a-E4

Отзывы:

Бренды по названию

Популярные бренды