NEC Express5800/R320a-E4 Скачать руководство пользователя страница 121

Страница: 121 / 186

Windows Setup 4-71

Verify that disk synchronization has started and the status of the DISK ACCESS LED and
RDR Utility display changes as the following table.

■

During synchronization

RDR Utility

DISK ACCESS LED

Condition Status

Synchronization
source disk

Green and blinking

Online

Synchronization
destination disk

Amber and blinking

Syncing

RDR Virtual Disk

－

Simplex Resync

(x = 0,4,8,…, 96)

IMPORTANT:

The time required for synchronization differs depending on the size.

As to the disk with the 73GB capacity, it takes about 80 minutes.

Setting dual disk configuration may not complete if you reboot the

system during the synchronization. Do not reboot the system before
synchronization process completes.

If the system stops by improper termination of Windows such as

pressing the power button, the entire synchronized disk area will be
resynchronized after rebooting the system.

Содержание Express5800/R320a-E4



























































































































































































Результаты поиска

Содержание Express5800/R320a-E4

Отзывы:

Бренды по названию

Популярные бренды

NEC Express5800/R320a-E4, Руководство пользователя

Результаты поиска

Содержание Express5800/R320a-E4

Отзывы:

Бренды по названию

Популярные бренды